Handbook of Applied Thermal Design

Передня обкладинка
CRC Press, 1 лют. 1999 р. - 720 стор.
Gives a foundation to the four principle facets of thermal design: heat transfer analysis, materials performance, heating and cooling technology, and instrumentation and control. The focus is on providing practical thermal design and development guidance across the spectrum of problem analysis, material applications, equipment specification, and sensor and control selection.
 

Вибрані сторінки

Зміст

Paul David AuCoin Product Specialist SolarWeston Houston Tex PART
1-4
David F Bartz Tecogen Inc Waltham Mass PART 5 CHAP
1-14
Conduction HeatTransfer Solutions 120
1-20
TwoPhase Heat Transfer 175
1-75
Radiation Heat Transfer 185
1-85
Thermophysical Properties of Selected Engineering Materials
1
Robert E Buckley Mohawk Associates Norwalk Conn PART
7
Characteristics and Application of Thermal Insulation
3-2
Electric Powered Heating
8-1
Anthony J Izbicki Senior Vice President Hood Co Inc Hamburg
8-6
Induction Heating 854
8-54
Laser Heating 869
8-69
Brian Jones Minco Products Inc Minneapolis Minn PART
9-12
Thermoelectric Refrigeration 925
9-27
HeatDriven Refrigeration 933
9-34
Expendable Coolants 940
9-40

Wilson A Clayton Director of Engineering HyCal Engineering El Monte
3-11
Kim T Gilbert Mirror Insulation Unit Diamond Power Specialty Com
3-42
Structural Materials in Thermal Design
4-1
HeatTransfer Fluids
4-47
Common Gases as HeatTransfer Fluids 528
24
Molten Salts 552
5-52
PhaseChange Thermal Storage Materials
6-2
Fusible Alloys 612
6-12
Refractories 622
6-22
Thermally Conductive Plastics 639
6-39
Bimetallic Materials 645
6-45
Heat Exchangers and Related Devices
7-1
HeatExchanger Design and Rating 724
7-24
HighPerformance HeatTransfer Surfaces 737
7-39
Heat Pipes 750
7-50
Air and LiquidCooled Heat Sinks 759
7-59
Combustion Heat from Clean Fuels 102
10-2
Longsworth APD Cryogenics Inc Allentown Pa PART
10-11
Cryogenic Fluids and Design Practice
11-1
Thermal Sensors
12-1
Jose G Martin Department of Mechanical and Energy Engineering Uni
12-6
Resistance Thermometry 1218
12-18
Bimetallic Thermometers 1229
12-29
FilledSystem Thermometers 1238
12-38
Radiation Thermometry 1247
12-47
Infrared Thermography 1257
12-57
Humidity Detectors 1271
12-71
Liquid Crystals 1277
12-77
Automatic Temperature Controls
13-1
Electronic Temperature Controllers 138
13-8
Appendix Classified Unit Conversions
Авторські права

Інші видання - Показати все

Handbook of Applied Thermal Design
Eric C. Guyer
Перегляд фрагмента - 1989

Загальні терміни та фрази

alloys aluminum applications boiling Btu/h Btu/lb carbon ceramic chemical components compressor condensation constant Convection Heat Convection Heat Transfer cooling corrosion cryogenic cylinder density diameter duct effect electrical element emittance energy equations factor fiber film fluid forced convection ft² furnace fusible alloys gases heat exchangers heat flux heat sink Heat Transfer heat-transfer coefficient heater high-temperature Inconel insulation laminar flow lb/ft³ lb/in² liquid load Mass Transfer materials maximum measured mechanical melting metal methods Natural Convection Nusselt number operating oxide parameters perature percent pipe plastic plate properties radiation radiosities range ratio refractory refrigerant resistance thermometer sensor shown in Fig silicon carbide specific heat spectral steel stress surface T₁ T₂ Table temperature thermal conductivity thermal insulations thermal resistance thermocouple thermometers tube Typical values valve vapor velocity viscosity wall wire

Посилання на книгу

Бібліографічна інформація

НазваHandbook of Applied Thermal Design
АвторEric C. Guyer
Виданняілюстроване, передрук, виправлене
ВидавецьCRC Press, 1999
ISBN1560328118, 9781560328117
Обсяг720 стор.
  
Експортувати бібліографічний описBiBTeX EndNote RefMan