Зображення сторінки
PDF
ePub

Switchboards for arc-lighting circuits.

the various parts of the back, and it may be added that the connections should be kept as close to the board as possible. A good example of a snugly arranged board is shown in Fig. 47, which is an end view and shows well the clear space back of the board, and also the way in which the wiring is arranged so as to not encroach upon the space.

Switchboards are often made in a number of panels so that they may be increased in capacity at any time without destroying their symmetry or crowding any of the parts together. A three-panel board of this type is shown in Figs. 48 and 49, the first showing the front and the second the back. The panels a and b are generator panels and are provided with a main switch, a field regulator, a circuit breaker, and an ammeter. The third panel c, is a distributing panel, and is provided with two circuit breakers, two single pole switches, one ammeter and one voltmeter. On the back of the board are also provided lightning arresters for all the conductors. This board is arranged for operating an electric railway, and it only requires one distributing panel, because the road is small. It will be noticed that this board is made up of panels that are duplicates of each other, so that if at any time it becomes necessary to enlarge the plant, the switchboard can also be enlarged by the addition of more panels.

Switchboards for arc-lighting circuits.

The construction of arc light switchboards is very simple in comparison with constant potential boards. This difference arises from the fact that each machine

Arc lighting.

is arranged so as to feed into a single circuit, and also because circuit breakers and voltmeters are not required. A simple arc light board for four generators is shown in Fig. 50. It consists of a marble slab which carries eight plug receptacles at the upper edge, and eight more at the bottom, and an ammeter in the central space. Eight wires

[graphic][merged small][merged small]

running from the terminals of four machines are connected with the eight lower receptacles, and eight line wires are connected with the eight upper receptacles. By means of the flexible cables shown, any one of the lower receptacles can be connected with any one of the upper ones, as is clearly indicated in the illustration. A

Arc lighting.

voltmeter is not required, owing to the fact that the e. m. f. of the generator is continually rising and falling in accordance with the demands of the circuit. If the num

The Derry-Collard Co, Ni,

Figure 51

Diagram of arc light board.

ber of lamps in service is increased, the e. m. f. must correspondingly increase, and if the number of lamps is re

Arc lighting.

duced, the voltage must also reduce. This variation in the e. m. f. is effected by the regulator of the machine. An ammeter is required, however, because the current must remain constant to keep the lights from varying in brilliancy. In the board shown in Fig. 50 there is only one ammeter; therefore, this can only be used from time to time to test the several circuits and ascertain whether the current strength is what it should be or not. In more complete and expensive boards, one ammeter is provided for each circuit, and this is left in service all the time so that the strength of the current may be observed without going to the trouble of cutting the instrument into the circuit.

The switchboard connections of an arc light system are clearly shown in Fig. 51, which is so simple a diagram that an extended explanation is not necessary. It will be noticed, however, that the number of receptacles or sockets is greater than in Fig. 50, there being five rows at the top and five at the bottom. The advantage of this arrangement is that by means of two short cables a machine whose terminals run to one end of the board can be connected with a circuit whose terminals are connected with the other end, and thus the confusion arising from the use of long cables is avoided. If there are only a few machines, this construction is of no particular advantage, but in cases where a large number of circuits are to be provided for it is.

In Fig. 51 the first machine is arranged to feed into one circuit only, the second machine supplies two circuits that are connected in series, and the third machine supplies three circuits connected in series. This way of connecting the circuits is not often used at, the present

Arc lighting.

time, but was quite common in former days when small size generators, ranging from sixteen to twenty-five lights, were to be found in most arc-lighting stations. With such machines there is no special objection to connecting a number in series as their combined e. m. f. is not more than that of one large generator. The connection of the circuits in series in the diagram serves to illustrate clearly the advantage of providing a number of sockets connected with each other in the manner indicated by the horizontal lines. As will be noticed, the second and third circuits are connected in series with each other, and with machine No. 2 without the aid of the horizontally connected sockets; but the last three circuits and the third machine are connected in series through the lower middle row of sockets by the use of two short cables, one running from the lower No. 6 terminal, and the other from the left side of the generator. The second machine could also be connected in this manner, as lower terminal No. 3 could be connected with the lower row of sockets, and the generator could be connected with the top row. In this particular case such an arrangement would be of no special advantage, as the cable from the lower machine terminal to lower 3 is not long and does not cross any of the other cables. In the case of the third machine, however, if a cable were run directly from lower 6 to the machine terminal, two cables would be crossed. As can be seen from this explanation, if the board were made of sufficient size to accommodate twenty or more generators, with an equal number, or more of circuits, the complication arising from direct cable connection from the machine to the circuit terminals would very great. All this complication could be avoided if

« НазадПродовжити »