Standard Practical Plumbing: An Exhaustive Treatise on All Branches of Plumbing Construction Including Drainage and Venting, Ventilation, Hot and Cold Water Supply and Circulation ...Norman W. Henley Publishing Company, 1910 - 396 стор. |
З цієї книги
Результати 1-5 із 51
Сторінка 25
... inch sizes are not standard sizes , and therefore not generally carried in stock , although many plumbers claim that they must have cloths of these odd dimen- sions . It is difficult to name any complete set of wiping cloths , as one ...
... inch sizes are not standard sizes , and therefore not generally carried in stock , although many plumbers claim that they must have cloths of these odd dimen- sions . It is difficult to name any complete set of wiping cloths , as one ...
Сторінка 26
... inch pipe thread . Through the hole a piece of pipe may be thrust , and used as a lever to wind up the spring in withdrawing it . A half - inch pipe may be screwed to the end of the spring , and by means of it , withdrawn from the pipe ...
... inch pipe thread . Through the hole a piece of pipe may be thrust , and used as a lever to wind up the spring in withdrawing it . A half - inch pipe may be screwed to the end of the spring , and by means of it , withdrawn from the pipe ...
Сторінка 31
... inch pipe . This is a point which the 4 - wheel cutter shown in the illustration overcomes , a point of considerable importance nowadays , as the use of two - inch pipe is constantly increasing , as it is a size which is being more ...
... inch pipe . This is a point which the 4 - wheel cutter shown in the illustration overcomes , a point of considerable importance nowadays , as the use of two - inch pipe is constantly increasing , as it is a size which is being more ...
Сторінка 45
... inch thick , and 14 It should be about 6 or 7 inches long , inches wide in the wide part . In getting the solder onto the joint , splash the solder onto the upper part of it and all around it . With the splash stick keep pulling the ...
... inch thick , and 14 It should be about 6 or 7 inches long , inches wide in the wide part . In getting the solder onto the joint , splash the solder onto the upper part of it and all around it . With the splash stick keep pulling the ...
Сторінка 48
... inches makes good looking work , and about 1 inches for a 4 - inch joint . Thus far , attention has been confined solely to the wiping of Soldering Union , Bent Iron Pipe 169 2 . Wiped Joint ४ Soldering Ripple foole Wiped Joint 76 ° 4 ...
... inches makes good looking work , and about 1 inches for a 4 - inch joint . Thus far , attention has been confined solely to the wiping of Soldering Union , Bent Iron Pipe 169 2 . Wiped Joint ४ Soldering Ripple foole Wiped Joint 76 ° 4 ...
Інші видання - Показати все
Standard Practical Plumbing: An Exhaustive Treatise On All Branches of ... Robert Macy Starbuck Попередній перегляд недоступний - 2022 |
Загальні терміни та фрази
50 cents action atmospheric pressure ball cock bath room Boiler Supply branch brass calking capillary action cellar chapter circulation pipe cleanout close cock coil cold construction continuous vent device drainage system drum trap Electric engineer ferrule filter filtered water fitting fixture flange floor flow pipe flush hard water heat horizontal hot water hot-water supply house drain house sewer inches installed Lavatory lead bend lead pipe liquid located Main Stack main trap main vent matter means metal method moleskin necessary O'CONOR SLOANE oakum opening outlet plug plumber plumbing system practical pressure pressure filter Price range boiler range connection roof seen in Fig sewage shown in Fig shows Sink siphon siphonage soil pipe solder steam surface tank tion trap seal trap vent vacuum valve ventilation Vert Walschaert Valve Gear water front water lift water supply water-closet wiped joint wiping cloths wrought iron