Gasolene Engines; Their Operation, Use and Care: A Comprehensive, Simple and Practical Work Treating of Gasolene Engines for Stationary, Marine Or Vehicle Use ...Norman W. Henley Publishing Company, 1912 - 275 стор. |
З цієї книги
Результати 1-5 із 25
Сторінка 84
... steel or bronze , and may be either cast or forged . The upper end , which fits inside the piston , is held in place by a hardened pin passing through the piston from one side to the other and known as the piston pin ( Fig . 42 ) ...
... steel or bronze , and may be either cast or forged . The upper end , which fits inside the piston , is held in place by a hardened pin passing through the piston from one side to the other and known as the piston pin ( Fig . 42 ) ...
Сторінка 85
... steel , aluminum or other metal , and may be made either solid , with one end removable ( Fig . 48 ) ; with split base ( Fig . 49 ) ; with both bearings or end plates separate ( Fig . 50 ) THEIR OPERATION , USE , AND CARE 85.
... steel , aluminum or other metal , and may be made either solid , with one end removable ( Fig . 48 ) ; with split base ( Fig . 49 ) ; with both bearings or end plates separate ( Fig . 50 ) THEIR OPERATION , USE , AND CARE 85.
Сторінка 90
... power to the machinery ; they should therefore be designed with a large excess of strength and should be forged from the highest grade of steel . Open- hearth .35 to 45 carbon steel is excellent material , 90 GASOLENE ENGINES.
... power to the machinery ; they should therefore be designed with a large excess of strength and should be forged from the highest grade of steel . Open- hearth .35 to 45 carbon steel is excellent material , 90 GASOLENE ENGINES.
Сторінка 91
... steel is excellent material , and after forging into shape it should be annealed , which relieves the strain from forging and renders the steel tough and strong . They should then be machined to 10000000000 Fig . 52. - Water Jacket ...
... steel is excellent material , and after forging into shape it should be annealed , which relieves the strain from forging and renders the steel tough and strong . They should then be machined to 10000000000 Fig . 52. - Water Jacket ...
Сторінка 94
... steel gears are to be avoided as far as possible unless of the worm or helical type , for bevel or spur gears of these metals are invariably noisy and wear rapidly . The bearing - metal gears used in the " American motors " run very ...
... steel gears are to be avoided as far as possible unless of the worm or helical type , for bevel or spur gears of these metals are invariably noisy and wear rapidly . The bearing - metal gears used in the " American motors " run very ...
Інші видання - Показати все
Gasolene Engines: Their Operation, Use and Care; A Comprehensive, Simple and ... A. Hyatt Verrill Попередній перегляд недоступний - 2017 |
Загальні терміни та фрази
50 cents adjustment armature Batteries bearings boat boilers bolt broken carburetor cause chamber charge of gas check valve clean cock coil compression Concrete connecting rod construction crank shaft cylinder device diam dynamo electrical electrical current electrode explosion fastened float valve fly-wheel Four-cycle Engine four-cycle motors fuel fully illustrated gas engine gases gasolene engines gasolene motors Gear Pump grease heat hole ignition illustrated in Fig intake jacket joints jump-spark kerosene Lathes leak Locomotive loose lubrication machine magneto make-and-break manufacture marine mechanical metal method molds muffler needle valve O'CONOR SLOANE opening operation piece piston plumbing plunger port PRACTICAL BOOKS pressure Price pump rings rotary valve screw screw threads shown in Fig spark plug speed spring stationary steam steel stroke tank thread timer tion trouble two-cycle motor Valve Gear vapor various vibrator Walschaert Valve Gear wheel wires worn