Зображення сторінки
PDF
ePub

72. Globes.

73. Spark Arresters and Nets.

74. Carbons.

75. Starting Plant and Instruction. 76. Renewal Parts.

77. Summary.

[merged small][ocr errors][merged small][merged small]

sets of carbons, a set consisting of

one upper and one lower carbon.

(See p. 46, sec. 25.)

(See p. 47, sec. 26.)

(See Note: p. 47, sec. 27.)

Each bidder shall fill out completely the

[blocks in formation]

Series or shunt wound

H. P. required to be delivered at pulley
at full load with no loss in the line

78. Switchboard Com plete.

SWITCHBOARD, APPARATUS, AND CONNECTIONS. This contractor shall furnish and erect the following apparatus and material:

One combination (material) switchboard with a capacity for circuits, and provided with the necessary sockets, plugs, main and

transfer cables, testing connections, and a suitable and convenient device for holding cables not in use. It shall be so arranged and marked that any circuit or series of circuits may be quickly connected with or disconnected from any dynamo with the least possible danger of short-circuits or error. Sockets shall be so designed that it is practically impossible to short-circuit, ground, or receive a shock from them. All connections with the dynamo leads shall be easily accessible. All wires used in making connections shall have

insulation. All plugs shall have well insulated wooden handles, and the cables shall be covered with soft-rubber tubing or equivalent as an extra precaution. All cables shall be of stranded wire.

All joints shall be soldered. All connections to switches, cut-outs, etc., shall be soldered or made with an approved form of lug or setscrew, in all cases care being taken to secure good and sufficient contact to prevent heating and insure permanency; when made with lugs or set-screws they shall be in plain sight and easily accessible for tightening. Connecting wires shall be so run and secured that crosses or grounds are impossible in the normal operation of the plant.

FIXTURES, ETC.

and Shades.

(Note. No set specification can be made for 79. Fixtures fixtures and shades; their character must be

80. Lamps.

determined wholly from individual requirements. See schedule, p. 107.)

This contractor shall furnish and deliver at the following number, sizes, and kinds of incandescent lamps:

[blocks in formation]

81. Sockets

and Receptacles.

stating, also, their make and the make of the socket for which they are adapted.

Lamps shall be guaranteed to have an average life of not less than hours if burned at their normal voltage. They shall burn with a white light, and shall not blacken under proper use. All lamps giving out or proving defective during the trial period of under normal and proper use shall be replaced without charge.

[ocr errors]

days

This contractor shall furnish and deliver at the following numbers and kinds of sockets and receptacles:

[blocks in formation]
[blocks in formation]

The building shall be wired to lets, switch outlets, (and lets) for the equivalent of

volt lamps. The wiring shall be

トリ

lamp out- 83. Outlets

raeter out

-c. P.,
(to outlets

only) (except for cut-outs and switches; cutouts and switches shall be furnished and installed complete). At each outlet the loose wire shall be neatly coiled and the ends carefully taped.

and Lights.

All wiring shall be for the parallel, two-wire 84. System. system of distribution.

in Pressure.

The fall of potential between the switch- 85. Variation board (centre of distribution) and the (farthest

lamp) shall not exceed at

load

per

cent. of the initial pressure; this difference to

[ocr errors][merged small][merged small][merged small][merged small][merged small]

All wire used throughout the installation shall be insulated with

86. Insula.

tion.

87. Insula

tion Resist

auce.

Each

(riser,

Federmain, and tap shall test

out with an insulation resistance of at least ohms. The entire installation shall test out with an insulation resistance of at least ohms divided by the sum of the number

of separate

risers,

feeders, mains, and taps.

S

[blocks in formation]
[merged small][merged small][merged small][ocr errors]

(Riser

Group No. 1 shall feed all lights (location),

Feeder

riser

group No. 2 shall feed, etc.

feeder

From the switchboard (or centre of dis

Feeders tribution) the

[merged small][merged small][ocr errors]

under cleats,

on insulators,

to

and thence up

in molding, etc.,

ward in (channels, wooden conduits, elevator shaft, air shaft, etc., with location) to their respective cut-out boxes.

« НазадПродовжити »