| Frank Eugene Kidder - 1892 - 1032 стор.
...cuts the difference of potential down to less than 300 volts. Rule 1O. Outside Conductors : Section/. All joints must be soldered, even if made with the...splices in all classes of wiring covered by these Rules. Rule 15. Outside Overhead Conductors : Rule 16. Underground Conductors : Section b. The cut-out required... | |
| Charles M. Davis - 1893 - 162 стор.
...300 volts. RULE 10. OUTSIDE CONDUCTOES. Section/. It is the sense of the Electrical Committee that all joints must be soldered, even if made with the...splices in all classes of wiring covered by these Rules. RULE 15. OUTSIDE OVERHEAD CONDUCTORS. Section 6. The cut-out required by this section must be placed... | |
| Richard Henry Pierce - 1896 - 234 стор.
...so spliced or jointed as to be both mechanically and electrically secure without solder. The joints must then be soldered, to insure preservation, and...splices in all classes of wiring covered by these i ules. K Telegraph, telephone and similar wires must not be placed on the same cross-arm with electric... | |
| Russell Robb - 1896 - 208 стор.
...to insure preservation, and covered with an insulation equal to that on the conductors. [Section/. All joints must be soldered, even if made with the...in all classes of wiring covered by these rules.] g. Telegraph, telephone, and similar wires must not be placed on the same cross-arm with electric light... | |
| Nehemiah Hawkins - 1896 - 570 стор.
...lengths of tube made for conduit work, nor when made without a head or flange on one end.] Sectiony. All joints must be soldered, even if made with the...splices in all classes of wiring covered by these Rules. 21. SPECIAL, WIRING : Section b. The insulating covering of the wire to be approved under this section... | |
| Earle Abbott Merrill - 1896 - 222 стор.
...current of 550 volts and after three minutes' electrification. (See List of Wires, page 202). Section /. All joints must be soldered, even if made with the...splices in all classes of wiring covered by these Rules. RULE 12. INTERIOR CONDUCTORS: — Section d. Insulation that will be approved for interior conductors... | |
| Nehemiah Hawkins - 1896 - 568 стор.
...submersion in lime water, with a current of 550 volts, and after three minutes' electrification. Section f. All joints must be soldered, even if made with the...splices in all classes of wiring covered by these Kules. RUI.B 12. INTERIOR CONDUCTORS : Section d. Insulation that will be approved for interior conductors... | |
| Earle Abbott Merrilol - 1896 - 232 стор.
...volts and after three minutes' electrification. (See List of Wires, page 202). Section /. All j oints must be soldered, even if made with the Mclntyre or...splicing device. This ruling applies to joints and splice's in all classes of wiring covered by these Rules. RULE 12. INTERIOR CONDUCTORS:— Section... | |
| Earle Abbott Merrill - 1896 - 232 стор.
...head or flange on one end. Section /. All joints must be soldered, even if made with the Mclntyre or other patent splicing device. This ruling applies...splices in all classes of wiring covered by these rules. RULE 21. SPECIAL WIRING: — Section b. The insulating covering of the wire to be approved under this... | |
| American Institute of Electrical Engineers - 1897 - 710 стор.
...wire, they must be soldered into lugs. All joints must be soldered, even if made with some form of patent splicing device. This ruling applies to joints...splices in all classes of wiring covered by these rules. d. Must be separated from contact with walls, floors timbers or partitions through which they may pass... | |
| |