Зображення сторінки
PDF
ePub

pump. The water used in some localities for cooling contains much matter either in suspension or solution which will form scale or a powdery deposit in the radiator tubes. It does not take much scale to seriously reduce the ratio of heat conduction between the heated water inside of the tube and the cooling air currents which

[graphic]

WATEM PASSAGES

BOTTOM WATER TASK

WATER PUMP

WATER SYSTEM DRAIN COCK
WATER PUMP DE coche

Fig. 171.—The Packard Cooling System, Showing All Important Com

ponents.

are circulated about their exterior. As cylinders are generally of cast iron, a certain amount of rust will be present in the water jacket, and this also may get into the radiator piping. If an antifreezing solution using some salt as a basis such as calcium-chloride is employed, after this has been circulated through the radiator and piping for a time it may deposit solid matter in the form of crystals in the piping or radiator. Anti-freezing solutions that include glycerine may have a chemical action due to the acid sometimes found in the cheap commercial grades of glycerine employed for this purpose. This chemical action results in the deterioration of the water jacket walls, and also contributes to the rust deposit.

cases,

Cleaning Sand from Water Jackets.-In some cases excessive heating of an engine has been found to be due to a retention of part of the sand core in the water jacket of the cylinder casting. This is very apt to be the case if the casting is in such form that the water jacket interior is inaccessible. On those types of unit castings where a large side plate is employed to close an opening that occupies practically the entire side of a water jacket, no difficulty obtains in cleaning out all core sand, but where this precaution is not taken and the core supported by prints of small size, there is considerable difficulty in clearing the casting in some

For those not familiar with foundry practice the writer may say that the core is that portion which is used in the mold to represent the space between the cylinder wall and water jacket, as it is necessary to use some such filler in the mold when pouring the molten metal into the impression left by the pattern to form the cylinder. Cores are usually made of fine sand held together by binding material, and in some cases with pieces of wire running through as a re-enforcement, the whole being baked to form one piece before it is placed in the mold. A piece of this core may become lodged in some angle or corner and remain there even though the greater portion of the core is removed by the foundryman. This may not become loose until the engine has been in use for some time, and then it may be carried into a pipe or opening and partially or wholly interrupt the water circulation. The piece of core may dissolve and deposit considerable sand in the water jacket which will collect in some corner where it may affect circulation. In order to remove all traces of sand, where mechanical means are not practical, an authority recommends a solution of hydrofluoric acid and water, the proportions being about one part acid to ten of water. This should be poured into the jacket and allowed to stand over night, which will loosen the sand or dissolve it. The cylinder jacket should be thoroughly drained and all traces of the acid removed by flushing thoroughly with hot water under pressure. Hydrofluoric acid is the only one that will attack sand, and it is well to remember that it has the same effect on glass which is usually indifferent to the action of the other common acids. Care must be taken, therefore, to keep it in the

special rubber container, in which it is received from the chemical supply house. While this chemical will also attack the metal of which the cylinder is composed, the diluted solution recommended will have no material effect in the short time required to thoroughly dissolve the sand.

It is not advisable to use the diluted acid in the water spaces of the radiator, as the brass or copper used in this part of the cooling system is much thinner than the material employed in the water jacket, and is also more easily attacked by the acid. For cleaning out the water spaces of a radiator a solution of potash or washing soda may be used. This will cut the rust and some forms of scale and will dissolve them or loosen them sufficiently so the deposits may be thoroughly flushed out with water or steam under pressure.

The solution will work more rapidly if it is brought to the boiling point before placing it in the radiator. The potash solution is also valuable in removing rust from the water jacket interior.

Incrustation is most commonly caused by carbonate of lime which is held in solution in some water as a bicarbonate ; therefore, when the water is heated the carbonic acid is driven off and the carbonate is precipitated in the form of a muddy deposit which hardens in the presence of heat into a nonconducting scale in those portions of the water jacket where the heat is greatest, and which remains in the form of a powdery deposit in the radiator tubes where the heat is not great enough to harden the sediment. Sometimes the deposit is sulphate of lime, this also being found in the water available in some localities. The reason that water contains so many impurities is because it is one of the best known solvents. Pure water is never found in nature and can only be obtained by a process of distillation. The purest natural water is rain, and if this is collected before it touches the earth it contains only such impurities as may be derived from the atmosphere, these consisting of gases in the open country such as nitrogen and carbon dioxide. That falling over towns absorbs quantities of acids and soluble salts. Rain water collected near the ocean contains chlorine. The source of water supply in many communities is some river flowing through or within a short distance. A large variety

[graphic][subsumed][subsumed][subsumed][subsumed][subsumed][subsumed][ocr errors][subsumed][subsumed][subsumed][subsumed][subsumed][subsumed][subsumed][subsumed]

Fig. 172.—Part Sectional View of the Packard Centrifugal Water Pump.

of substances may be found in solution in river water, the main element being derived from the rocks through which the water of the springs which have fed the river has percolated. Then, again, river water is often contaminated by the drainage of towns or of manufacturing establishments situated on the banks of the river. Spring waters also contain many salts and minerals. Water that has been obtained from ponds is often rich in vegetable matter. As it is not practical for the motorist to use distilled water for filling the radiator and water jackets, it is apparent that the water obtained from the other sources will contain impurities in various amounts. If the water is very hard or contains much salt, it will be well for the motorist to save rain water for use in the cooling system. The best solvent to use depends entirely upon the composition of the water, and as this varies in all portions of the world it is not possible to enumerate the best chemicals for removing incrustation or to neutralize the material in solution. The advice of a local chemist should be sought in matters of this kind.

Deterioration of Rubber Hose.-In order to avoid fracture of the water manifolds from vibration, as would be the case if these were attached to the radiator by nonflexible metallic connections, it is customary to interpose pieces of rubber hose between the radiator and the manifolds as shown at Fig. 169, A, and where the manifolds are the built-up form; rubber hose often forms an important item of the piping system as shown at Fig. 171. While it is imperative to use the best quality steam hose for this purpose, even this material may depreciate in use. A certain amount of oil and grease will find its way into the cooling system, usually from the grease cups used to lubricate the water pump bearings. This causes the hose to rot inside as the oil has a chemical action upon the rubber. Strips of the interior lining may become detached and may interfere with water circulation by constricting the bore of the hose. If anti-freezing solutions containing glycerine are used, depreciation of the hose is inevitable. The best remedy is replacement of the defective hose with new, as this material is relatively inexpensive, in fact, one may obtain special hose connections for use on all the popular makes of cars from the large automobile

« НазадПродовжити »