Зображення сторінки
PDF
ePub

83. Outlets and Lights.

84, System.

INTERIOR WIRING.

Alternating or Direct Current, Two-Wire
System. -

The building shall be wired to — lamp outlets, – switch outlets, (and — meter outlets) for the equivalent of —, - ampere, — volt lamps. The wiring shall be (to outlets only) (except for cut-outs and switches; cut-outs and switches shall be furnished and installed complete). At each outlet the loose wire shall be neatly coiled and the ends care

fully taped.

All wiring shall be for the parallel two-wire system of distribution.

85. Variation The fall of potential between the

in Pressure.

switchboard (centre of distribution) and the (farthest lamp) shall not exceed at

— load — per cent. of the initial pressure; this difference to be divided as

follows: | Hors |– per cent., mains

— per cent., taps — per cent.

All wire used throughout the installa- 86. Insulation. tion shall be insulated with —.

riser - 87. Insulati Each) fee der, | main, and tap shall ote.”

test out with an insulation resistance of at least — ohms.

[merged small][ocr errors][merged small]

feeders, shall be carried to the following points: Riser riser Group - No. 1 to —, 3 group - No. 2 Feeder feeder to —, etc.

Riser
Group - No. 1 shall feed all lights (lo-
Feeder

riser cation), X group - No. 2 shall feed, etc. feeder

* * From the switchboard (or centre of disRisers

[ocr errors]

under cleats,
on insulators,
in moulding,
in conduit, etc., J

upward in (channels, wooden conduits, elevator shaft, air shaft, etc., with location) to their respective cut-out boxes.

to —, and thence

[ocr errors]

- riser . . termi- no.a. From the feeder | cut outboxes mains ary distribution boxes. under cleats, - - lators hall I'I’l on insul 3. t shall be carried: i. molding, O in conduit, etc.,

secondary cut-out boxes where all tap

lines shall centre. From | riser |NO. 1.

feeder shall be carried — mains terminating at - riser —, from: feeder |No. 2, etc.

91. Taps. (Note.—In certain cases it is advisable

to run the circuits in such a manner that
no room shall be dependent on one cir-
cuit only; if so desired it should be add-
ed under this heading.)
riser
From the }o (* boxes dis-
IIla II).
tributing circuits shall be run to the
various outlets as specified in the sched-
ule and located on the plans. The
under cleats,

- on insulators wires shal - - 5 l be run in molding, 1I].

in conduit, etc., such a manner that the highest possible insulation shall be maintained under all circumstances.

Except in case of single outlets for a group of lamps and circuits specifically mentioned no distributing circuit shall carry over — amperes. Distributing circuits shall be of one size of wire throughout their entire length.

Throughout the installation joints shall be avoided where possible; where abso

[ocr errors]

92. Joints.

93. Cut-Out and Switch Cabinets.

lutely necessary they must be made mechanically strong and secure, carefully soldered, wiped free from any moisture and excess of flux and so taped and compounded that the insulation of the joints shall be equal to the original insulation; the solder shall be relied on only to give a good electrical connection.

(Note.—A complete description of the cabinets should be given covering material, doors, hinges, locks, finish, etc.; also stating what parts, if any, will be furnished by other contractors, specifying what switches are to be placed in the cabinets, and locating and describing cabinets for switches alone if such are to be provided; if name plates are to be furnished so specify and describe.)

- risers, The terminals of all | feeders, | Isla IIlS

and taps shall be brought together in cabinets at the points designated in this specification and on the plans. (If wiring contractor does not furnish cut-outs and

« НазадПродовжити »